Page 1 of 2

Motec CDIs

Posted: Thu Mar 29, 2012 6:24 pm
by Dgeoff33
Does anyone know what the NC35 Motec CDI looks like? I have a bike with what is supposed to be a Motec CDI but as I have never seen one, I can't be sure it is.

It also has "ABR 09 STAGE 3 MAP#4" written on it, i'm guessing it has been through Aly Baileys hands at some point!!

Re: Motec CDIs

Posted: Thu Mar 29, 2012 6:31 pm
by Dgeoff33
Just been and took some pics.

Image
Image

Re: Motec CDIs

Posted: Thu Mar 29, 2012 6:59 pm
by Drunkn Munky
Think james had one a while back mate but im sure aly will be along to confirm what it is soon, chances are the motor in the bike is stage 3 tuned then, lucky git!! and a ohlins shock to go with it aswell!

Re: Motec CDIs

Posted: Thu Mar 29, 2012 7:02 pm
by CRM
geoff33 wrote: It also has "ABR 09 STAGE 3 MAP#4" written on it, i'm guessing it has been through Aly Baileys hands at some point!!
as has around 50% of bikes in the UK i am willing to bet

Re: Motec CDIs

Posted: Thu Mar 29, 2012 7:15 pm
by Dgeoff33
I have sent Aly a mail but not heard back yet.

You're right Tony, it does indeed have an Ohlins shock, and Maxton fork internals, it also has some writing on the motor but I haven't had a proper look, the panels are coming off at the weekend so i'll know more then.

Re: Motec CDIs

Posted: Thu Mar 29, 2012 7:22 pm
by Drunkn Munky
Is this the RVF your brought off ebay, the one that had been on there a while?

Re: Motec CDIs

Posted: Thu Mar 29, 2012 8:04 pm
by Dgeoff33
It certainly is.

Re: Motec CDIs

Posted: Thu Mar 29, 2012 9:09 pm
by abrmoto
geoff33 wrote:I have sent Aly a mail but not heard back yet.

You're right Tony, it does indeed have an Ohlins shock, and Maxton fork internals, it also has some writing on the motor but I haven't had a proper look, the panels are coming off at the weekend so i'll know more then.
I have had no mail??

Can tell you one thing for sure its not a Motec!!

And another dont get water in it or will be reduced to scrap in a day!! ;) :( :o

They are very good, basically fully adjustable ignition, but no where near as user friendly as a Ignitec or the like, really for Pro Dyno use only.
I ran these on my bikes from 04-06, but swapped back to Chipped HRC CDi after getting continual starting problems. Showed god BHP on Dyno but everything needed to be spot on. Have since changed again to Dynopro programmable ignitions.

What you have there was over £1000 new, and also needed an amplifier for the spark circuit.
As long as map not been messed with was set up for my #1 bike running RLR stage 3 tune. Sold it back in 07, cant remember who to, but was loom and ignition only, dont think will have a stage 3 motor in that bike.

Does it start ok??

Al

Re: Motec CDIs

Posted: Thu Mar 29, 2012 9:23 pm
by ibby4585
I love things like this! :popcorn:

Re: Motec CDIs

Posted: Thu Mar 29, 2012 11:29 pm
by micpec
ibby4585 wrote:I love things like this! :popcorn:
Me too! It's like a Atomic Fireball candy... :popcorn: