Another 'spare' bike
-
Drunkn Munky
- Site Supporter
- Posts: 6313
- Joined: Thu May 01, 2008 9:37 am
- Bike owned: NC30 MC21 TZR FZR GSXR RG MITO
- Location: Kent
Re: Another 'spare' bike
Looking good pal, pop em round next week if you like
-
Tim400GB
- Site Supporter
- Posts: 753
- Joined: Mon Jan 04, 2010 7:24 pm
- Bike owned: 1 x NC30, 2 x NC32.5,
- Location: SE Greater London
-
Tim400GB
- Site Supporter
- Posts: 753
- Joined: Mon Jan 04, 2010 7:24 pm
- Bike owned: 1 x NC30, 2 x NC32.5,
- Location: SE Greater London
Re: Another 'spare' bike
Ok so the bike looks like this now (cheers to DrunknMunky for glossing them) with all the bodywork on properly. And it's TT style screen and quick fill fuel cap.
I have a full set of TT Legends graphics and a couple of nc30 ones.
Was going to do a bit of a mix between these. Any opinions? I struggling a tad, don't know what to do
Also got my horn button wired up.
I have a full set of TT Legends graphics and a couple of nc30 ones.
Was going to do a bit of a mix between these. Any opinions? I struggling a tad, don't know what to do
Also got my horn button wired up.
-
Tim400GB
- Site Supporter
- Posts: 753
- Joined: Mon Jan 04, 2010 7:24 pm
- Bike owned: 1 x NC30, 2 x NC32.5,
- Location: SE Greater London
Re: Another 'spare' bike
Sigma speedo all mounted, along with the RVF wheels.
Jobs to do:
Bleed rear brake (and refit seat unit)
Fit tank pad and side grippers
Decide on and fit graphics
Buy and fit reg plate
Tax & mot
Shake down run
Track day!
Jobs to do:
Bleed rear brake (and refit seat unit)
Fit tank pad and side grippers
Decide on and fit graphics
Buy and fit reg plate
Tax & mot
Shake down run
Track day!
-
GeeTee
- NWAA Supporter
- Posts: 141
- Joined: Mon Jan 20, 2014 1:27 am
- Bike owned: NC30 & GSXR750K4
- Location: Dartford, Kent, United Kingdom
Re: Another 'spare' bike
Looks great 
I went for a similar retro DIY colour scheme on my own track bike
I went for a similar retro DIY colour scheme on my own track bike
-
Zippy
- Site Supporter
- Posts: 684
- Joined: Tue Mar 24, 2009 1:41 pm
- Location: South West
Re: Another 'spare' bike
Are you doing Cadwell on it?
-
Tim400GB
- Site Supporter
- Posts: 753
- Joined: Mon Jan 04, 2010 7:24 pm
- Bike owned: 1 x NC30, 2 x NC32.5,
- Location: SE Greater London
Re: Another 'spare' bike
When is it?
Got a horrible feeling I'm with the team in Germany for the NitrOlymX
Got a horrible feeling I'm with the team in Germany for the NitrOlymX
-
Zippy
- Site Supporter
- Posts: 684
- Joined: Tue Mar 24, 2009 1:41 pm
- Location: South West
Re: Another 'spare' bike
Next weekend :-)
-
Tim400GB
- Site Supporter
- Posts: 753
- Joined: Mon Jan 04, 2010 7:24 pm
- Bike owned: 1 x NC30, 2 x NC32.5,
- Location: SE Greater London
Re: Another 'spare' bike
So after nearly getting the bike done the calipers and right fork leg have decided to start leaking.
New seal set from Harrison Billet arrived
New fork seal set from David Silver arrived
And using this as an excuse a fork upgrade kit from Rick Oliver (many thanks for the swift delivery Rick) has now arrived too.
Hopefully be getting into the garage saturday to crack on with it all
New seal set from Harrison Billet arrived
New fork seal set from David Silver arrived
And using this as an excuse a fork upgrade kit from Rick Oliver (many thanks for the swift delivery Rick) has now arrived too.
Hopefully be getting into the garage saturday to crack on with it all
-
Tim400GB
- Site Supporter
- Posts: 753
- Joined: Mon Jan 04, 2010 7:24 pm
- Bike owned: 1 x NC30, 2 x NC32.5,
- Location: SE Greater London
Re: Another 'spare' bike
So today was a fairly productive day, and a busy one so I didn't manage to get many pictures.
The forks were taken off, seals replaced along with the springs, spacers and fluid. Then everything remounted.
Here's the old bits that came out.
The rear brake is now all bled up.
The issue came to the Billet calipers, they came apart ok but on assembly the pistons seem to be pinching the new seals. Not a happy bunny. Harrison being closed on Saturdays, so no tech advice available. To be continued.
The forks were taken off, seals replaced along with the springs, spacers and fluid. Then everything remounted.
Here's the old bits that came out.
The rear brake is now all bled up.
The issue came to the Billet calipers, they came apart ok but on assembly the pistons seem to be pinching the new seals. Not a happy bunny. Harrison being closed on Saturdays, so no tech advice available. To be continued.