GoPRO HD

And Yeah you could fabricate on easily if you have the tools.

You could do it to an NC30/35 using the same clutchrod / sprocket cover as it'll just bolt on.

However the NC30/35 speedo is driven off the sprocket and the NC2x is drive off the wheel so you'd need to mod the sprocket cover to hold the speedo drive :)

Shouldn't be too difficult

It would make an interesting conversion.

Neosophist wrote: However the NC30/35 speedo is driven off the sprocket and the NC2x is drive off the wheel so you'd need to mod the sprocket cover to hold the speedo drive :)

Or run it off the front wheel - then no hassles when you change the gearing!

Cammo wrote:It would make an interesting conversion.

Neosophist wrote: However the NC30/35 speedo is driven off the sprocket and the NC2x is drive off the wheel so you'd need to mod the sprocket cover to hold the speedo drive :)

Or run it off the front wheel - then no hassles when you change the gearing!

I thought about that one, but the wheels are different so *shrug* seemed easier to mod the sprocket cover :) anythings possible though

so lets have a list of bits needed for the mod then ,this may be something to do this winter.

Right then, i have found out the easiest way to do this is by using bits from the nc21; clutch master cylinger £30 ish, clutch slave cylinder £15 ish, pushrod £?, sprocket cover £15 ish, and hydraulic hose £20 is hand afew bolts £9 ish. Then theres the brake master cylinder to match.

Prices are aprox as they are just what i have found on ebay.

The push rod could be duplicated if i could find one to get duplicated!. Maybee a nc21 owner could remove theirs and get some made up, or lend it to me and i will get some made up

terryvxr8 wrote:Right then, i have found out the easiest way to do this is by using bits from the nc21; clutch master cylinger £30 ish, clutch slave cylinder £15 ish, pushrod £?, sprocket cover £15 ish, and hydraulic hose £20 is hand afew bolts £9 ish. Then theres the brake master cylinder to match.

Prices are aprox as they are just what i have found on ebay.

The push rod could be duplicated if i could find one to get duplicated!. Maybee a nc21 owner could remove theirs and get some made up, or lend it to me and i will get some made up

It's about 1.5cm longer than the NC24 pushrod.

I have an NC21 clutch master cylinder / lever and slave cylinder & sporocket cover i found in a bag yesterday, should have a hydraulic hose too, not sure about the pushrd thogugh.

You can have it for £20 if you want :)

Neosophist wrote:

terryvxr8 wrote:Right then, i have found out the easiest way to do this is by using bits from the nc21; clutch master cylinger £30 ish, clutch slave cylinder £15 ish, pushrod £?, sprocket cover £15 ish, and hydraulic hose £20 is hand afew bolts £9 ish. Then theres the brake master cylinder to match.

Prices are aprox as they are just what i have found on ebay.

The push rod could be duplicated if i could find one to get duplicated!. Maybee a nc21 owner could remove theirs and get some made up, or lend it to me and i will get some made up

It's about 1.5cm longer than the NC24 pushrod.

I have an NC21 clutch master cylinder / lever and slave cylinder & sporocket cover i found in a bag yesterday, should have a hydraulic hose too, not sure about the pushrd thogugh.

You can have it for £20 if you want :)

Sounds good to me, especially if you have the pushrod. I cant pm you as im not allowed!. My email is terrygrant@hotmail.co.uk

Ok i'll pop up the garage tomorrow and see what parts I have.

The Master cylinder / clutch lever / slave cylinder and sprokcet cover I have right here, im sure I have a hyrdaulic hose too. i'll check for you

Thanks for that

what size is the stock clutch master cylinder as i wanna find one that has a bottle like the brake lever rather than the metal res.

also if you guys see any of these parts cheap give me a shout as i'm going to try and fit one of these to an NC30