FZR 400 RRSP inlet manifolds.
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Site Supporter
- Reactions:
- Posts: 9490
- Joined: Tue Apr 29, 2008 8:59 pm
- Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
- Location: Lundin Taan
Re: FZR 400 RRSP inlet manifolds.
I don't know - I cant really guess at it either.
-
- Settled in member
- Reactions:
- Posts: 123
- Joined: Sun Nov 08, 2015 9:23 am
Re: FZR 400 RRSP inlet manifolds.
[quote="Shimmiel"]Hi friends, my bike had the same problem. New rubbers on 3TJ can not be found. But the inlet pipes with FZR600 (3HE) have a similar diameter but a larger height. Will the intake rubbers from 3HE fit to 3TJ and whether the airbox rests in the fuel tank? What do you think? Thanks [Yep, hit the same problem using 1wg inlets.Now gone back to 3tj ones which although show cracking on the mouths around the outside do look good still on the inside. Cant think of another way round this at the moment. Sorry if not much help.
-
- Settled in member
- Reactions:
- Posts: 4
- Joined: Mon May 16, 2011 3:07 pm
- Bike owned: FZR400RR 3TJ1
- Location: Russia/Rostov-na-Donu
- Contact:
Re: FZR 400 RRSP inlet manifolds.
I solved my problem. When I changed the spark plugs, I was distracted by a phone call and did not tighten them . As a result, there were air leaks at idle and the engine was not working properly.
-
- Site Supporter
- Reactions:
- Posts: 9490
- Joined: Tue Apr 29, 2008 8:59 pm
- Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
- Location: Lundin Taan
Re: FZR 400 RRSP inlet manifolds.
Cool / Doh !!!
-
- Settled in member
- Reactions:
- Posts: 123
- Joined: Sun Nov 08, 2015 9:23 am
Re: FZR 400 RRSP inlet manifolds.
Hi all, just about given up on the 3tj carbs as keps missing.Put some rally clean 3en carbs on and running in all 4 at last.Only problem is it is ticking over at 4000rpm. Cant seem to turn it down even though some slack on pull cable and slides appear fully shut.Dont think choke is sticking either.
-
- Settled in member
- Reactions:
- Posts: 123
- Joined: Sun Nov 08, 2015 9:23 am
Re: FZR 400 RRSP inlet manifolds.
Just a couple of pics.Using tsptalk now as given up on photobucket.
Sent from my GT-I9505 using Tapatalk
Sent from my GT-I9505 using Tapatalk
-
- Site Supporter
- Reactions:
- Posts: 9490
- Joined: Tue Apr 29, 2008 8:59 pm
- Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
- Location: Lundin Taan
Re: FZR 400 RRSP inlet manifolds.
You could be running lean on the idle jets or the needles ??? That would make it run fast1966baz wrote:Hi all, just about given up on the 3tj carbs as keps missing.Put some rally clean 3en carbs on and running in all 4 at last.Only problem is it is ticking over at 4000rpm. Cant seem to turn it down even though some slack on pull cable and slides appear fully shut.Dont think choke is sticking either.
-
- Settled in member
- Reactions:
- Posts: 123
- Joined: Sun Nov 08, 2015 9:23 am
Re: FZR 400 RRSP inlet manifolds.
Thanks Evil, I had wondered in the back of my mind about that. Ideally I need to get the original carbs sorted . One of the jets wont budge which I think is blocked. I wont give up at this stage even last case scenario sending the carbs to Allens to be refurbed. ps. finally found out that the bike is no.10 of the 100 UK models .Cheers.
-
- Site Supporter
- Reactions:
- Posts: 9490
- Joined: Tue Apr 29, 2008 8:59 pm
- Bike owned: Bimota SB6 Yamaha FZR 3TJ x2
- Location: Lundin Taan
Re: FZR 400 RRSP inlet manifolds.
Cool
You cant use a soldering toach (from Maplins) and heat the carb body around the jet then put an ice cube on the jet itself for some rapid cooling ??? I'm assuming this is a main other wise you need a small easyout
You cant use a soldering toach (from Maplins) and heat the carb body around the jet then put an ice cube on the jet itself for some rapid cooling ??? I'm assuming this is a main other wise you need a small easyout
-
- Settled in member
- Reactions:
- Posts: 123
- Joined: Sun Nov 08, 2015 9:23 am
Re: FZR 400 RRSP inlet manifolds.
Thanks Evil, Its the jet sunken in next to the 2 main jets. Not easy to get to as the top is a bit chewed up. What's an 'easy out ' Chicken.