Serious question
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Serious question
Hi all,
I have recently bought an nc23 that I plan to take parading with the CRMC.
What I would like to know is if the swing arm can be drilled and tapped to accept paddock stand bobbins? Or is this considered very bad practice?
All answers gratefully received.
Thanks
Ian
I have recently bought an nc23 that I plan to take parading with the CRMC.
What I would like to know is if the swing arm can be drilled and tapped to accept paddock stand bobbins? Or is this considered very bad practice?
All answers gratefully received.
Thanks
Ian
-
- Site Supporter
- Reactions:
- Posts: 1269
- Joined: Tue Apr 29, 2008 9:37 pm
- Bike owned: NC29 CBR600F
- Location: Lancashire
Re: Serious question
People drill the swingarm to use a sharkfin to stop their limbs getting caught between the chain and rear sprocket. Don't know if the swingarm would be strong enough for use with a paddock stand though.
How about getting a steel/aluminium bar and tapping a thread down the centre then getting that welded onto the bottom of the swingarm.
Just a thought
How about getting a steel/aluminium bar and tapping a thread down the centre then getting that welded onto the bottom of the swingarm.
Just a thought
Last edited by cbr400rrn on Thu May 25, 2017 11:27 pm, edited 1 time in total.
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Re: Serious question
Thanks for that.
I have notice that the rear wheel spindle is hollow, so I might just poke a rod through that and use it as the lifting bar.
Cheers
Ian
I have notice that the rear wheel spindle is hollow, so I might just poke a rod through that and use it as the lifting bar.
Cheers
Ian
-
- NWAA Supporter
- Reactions:
- Posts: 465
- Joined: Thu Apr 09, 2015 1:55 pm
- Location: Gravesend
Re: Serious question
I just use this type of stand with my NC23 http://www.ebay.co.uk/itm/REAR-Paddock- ... xyiOxR3TMN
No need for bobbins - you might need to fit some washers between the R clip and outside of the stand frame to bring the cups out to the right width.
Isn't the NC23 too modern for the CRMC and water cooled too (I used to marshal for them so only joking!)
No need for bobbins - you might need to fit some washers between the R clip and outside of the stand frame to bring the cups out to the right width.
Isn't the NC23 too modern for the CRMC and water cooled too (I used to marshal for them so only joking!)
Last edited by CB1pod70 on Mon May 22, 2017 11:44 pm, edited 1 time in total.
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Re: Serious question
Hi ...pod70
You are right the nc23 is too new to race with the club, but I will only be parading so the eligibility officer is a bit more relaxed about it. The coolant issue is overcome as long as it is just water in the system.
Will look at those stands instead I think, good call.
Cheers
Ian
You are right the nc23 is too new to race with the club, but I will only be parading so the eligibility officer is a bit more relaxed about it. The coolant issue is overcome as long as it is just water in the system.
Will look at those stands instead I think, good call.
Cheers
Ian
-
- Site Supporter
- Reactions:
- Posts: 2807
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Re: Serious question
...pod70.
Hi Andrew
Nice to meet you at CP at the weekend. Had some great rides, unfortunately you had gone by then, the 400/4 went really well.
Thanks for all the advice re: getting my NC23 ready for next year.
Hope to see you again.
Ian
Hi Andrew
Nice to meet you at CP at the weekend. Had some great rides, unfortunately you had gone by then, the 400/4 went really well.
Thanks for all the advice re: getting my NC23 ready for next year.
Hope to see you again.
Ian
-
- NWAA Supporter
- Reactions:
- Posts: 465
- Joined: Thu Apr 09, 2015 1:55 pm
- Location: Gravesend
Re: Serious question
Good to meet you too. Typically the weather seemed to rapidly clear once I had left.
We're all back at Cadwell on 24th & 25th June with the Classic Bikes Trackdays crew - there might be a place in the middleweights (sunday only) if you fancy joining us
We're all back at Cadwell on 24th & 25th June with the Classic Bikes Trackdays crew - there might be a place in the middleweights (sunday only) if you fancy joining us
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Re: Serious question
Would do, but it is a birthday/wedding anniversary weekend. so I best say not this time.
Take care all who are going.
Ian
Take care all who are going.
Ian
-
- Regular Member
- Reactions:
- Posts: 695
- Joined: Wed Jun 03, 2009 9:39 pm
- Bike owned: Cbr400rr nc29 type8 NSR250
- Location: West Midlands