Nc30 engine paint??

Post by **V4beermonster** » Wed Nov 28, 2012 11:50 pm

Ok starting on the restoration all stripped and in the clean, coat, rebuild all coming along soon. Engine checked compression,valve clearances ect. Turns out bike only done around 4000 miles before it as crashed. Anyway,, what's the best piant to refinish the engine in? It will be Vapour blasted Friday ready to be painted

Post by **Delboy** » Thu Nov 29, 2012 8:32 am

I'm at work at the m'ment but I have a can in the garage that I used on the clutch case, perfect match and has stood the test of time...will let you know when I get home.

Post by **V4beermonster** » Thu Nov 29, 2012 10:13 am

Super cheers Derek will be painting the whole block

Post by **Delboy** » Thu Nov 29, 2012 6:34 pm

It's Ford Metalic Graphite Grey then covered in high temperature laquer, as near as perfect match to original
Here's one I prepared I earlier

[img]http://i95.photobucket.com/albums/ ... .jpg[/img]

scotjell · Post by **scotjell** » Fri Nov 30, 2012 4:55 pm

Mines going for a media type blast. Casings all stripped as are the heads. Believe it or not mine are going to get powder coated. Will save myself a few quid as I've got someone to do the blasting as he's red praying the panels also. I'll get them back and do the time consuming bit of masking them up and dropping them to the local powder coaters. Should be a good result. The quote I had from a single bloke doing the lot was £500!!!!

Post by **VFRkieran** » Sat Dec 01, 2012 1:34 am

Derek do you remember where you bought the paint from? Also how did you prep the casing for paint? Ive got a mint RVF clutch cover that will obviosly need painting up to match the rest of the 30 engine.

Post by **Delboy** » Sat Dec 01, 2012 8:11 am

Gave the casing quick rub with wet n dry (400 grit I think) thorough de-grease then it was Halfrauds own spray then a few coats of a decent high heat proof laquer.

pip · Post by **pip** » Sat Dec 01, 2012 8:33 am

Oooh, great info

Post by **VFRkieran** » Sat Dec 01, 2012 7:11 pm

Much apreciated mate, i had a look on RS paints last night and found that under the paints for the RC30 an engine paint is listed http://www.rsbikepaint.com/en-gb/shop-p ... n&22207=on

Im pretty sure that the engine colour on the NC30's bigger brother is exactly the same, however buying that from RS paints would cost £25 just for a 400mil can of paint, thats without including the Etch primer and laquer that they say you would need, needless to say ive gone for the cheaper option to see how that works out.

Post by **NGneer** » Sat Dec 01, 2012 7:39 pm

scotjell wrote:Mines going for a media type blast. Casings all stripped as are the heads. Believe it or not mine are going to get powder coated. Will save myself a few quid as I've got someone to do the blasting as he's red praying the panels also. I'll get them back and do the time consuming bit of masking them up and dropping them to the local powder coaters. Should be a good result. The quote I had from a single bloke doing the lot was £500!!!!

Scot - are you going conventional black/dark bronz sort of colour.....

or going for something more erm ........ funky

Looking forward to seeing how the powder coat works out (got a similar idea brewing)

Nc30 engine paint??

Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??

Re: Nc30 engine paint??