open dyno day 16/07/11

Post by **lloydiecbr** » Fri Apr 15, 2011 12:57 pm

if enough interest kev at projex motorcycles in cradley heath Birmingham will hold a open dyno day £10 a run
and he will also have the fireblade wheelie machine there to have a go on £15
http://youtu.be/U9Y_XjcKxgY

Post by **porndoguk** » Fri Apr 15, 2011 9:04 pm

that wheelie machine is insane!

i think the NC30's would have a problem getting there rear wheel to mount into that rear axel thinggy?

ill probally tag along as im booked in for tomorrow,
why could this have been aranged for tomorrow

Post by **lloydiecbr** » Fri Apr 15, 2011 10:03 pm

you dont use your bike on the wheelie machine the blade stays on it ,
i was at kevs today with my firestorm and i asked him when the next dyno day was and he said set one up

Post by **porndoguk** » Sat Apr 16, 2011 9:56 pm

saw that wheelie machine in action today! a really scary bit of kit i darnt put one of our bikes on it anyway!

but its great thought, and i might have a go in july,

i will be getting the bike dynoed again after todays results. lets hope for an improvment :D

so you can stick my name down

Post by **porndoguk** » Sat Apr 16, 2011 9:56 pm

saw that wheelie machine in action today! a really scary bit of kit i darnt put one of our bikes on it anyway!

but its great thought, and i might have a go in july,

i will be getting the bike dynoed again after todays results. lets hope for an improvment :D

so you can stick my name down

Post by **Drunkn Munky** » Sat Apr 16, 2011 10:20 pm

I think ill come along and see how the rvf is shaping up.

Ricky, did you say kev has the ignitech software ready to conect? i'll have the TPS ready by then so some dyno time to dial that in would be good. Im going to run open carbs with just a foam panel on the RLR motor, same setup as marks super smooth NC, Be good to see if the TPS actually makes any difference.

Post by **porndoguk** » Sat Apr 16, 2011 10:32 pm

Drunkn Munky wrote:I think ill come along and see how the rvf is shaping up.

Ricky, did you say kev has the ignitech software ready to conect? i'll have the TPS ready by then so some dyno time to dial that in would be good. Im going to run open carbs with just a foam panel on the RLR motor, same setup as marks super smooth NC, Be good to see if the TPS actually makes any difference.

yes me and neosophist installed it onto his computer, but not sure if he will delete it afterwards he was really impressed with the ease of the ignitech to use etc, and that we left it running whilst he was dynoing the bike which he thought was good.

and how fast it uploads and downloads.

the Stock 2 Map and the Standard NC30 Map offer no difference in HP, BTW.

so it really needs some mapping work done whilst on the dyno TBH.

Post by **Neosophist** » Thu Apr 28, 2011 5:43 pm

If i'm around i'll be there.

Top Secret Super Special Awesome Project should be ready by then

Post by **porndoguk** » Thu Apr 28, 2011 5:45 pm

Neosophist wrote:If i'm around i'll be there.

Top Secret Super Special Awesome Project should be ready by then

i wont ask then,

DK-Tandy · Post by **DK-Tandy** » Mon May 23, 2011 9:43 am

is this still happening,, i wouldnt mind going

open dyno day 16/07/11

open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11

Re: open dyno day 16/07/11