NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

MexicanGringo · Post by **MexicanGringo** » Wed May 05, 2010 9:23 am

Maybe use new cam holder bolts when you put it back together, the others ones will be elongated and weakened

Old Painless · Post by **Old Painless** » Wed May 05, 2010 10:59 am

Camshafts do snap but its a 1 in a million chance and should only happen in old age.

Just unlucky i guess.

Post by **CMSMJ1** » Wed May 05, 2010 11:00 am

I bought an NC30 a while back and upon checking the engine I found the reason it sounded like a tractor was it had a snapped camshaft and knackered main bearings.... Poor old moto..

pagan1001 · Post by **pagan1001** » Tue May 11, 2010 12:31 am

Okay got the new head on but encountered a new problem. I took the valve clearances but for cylinder 3 exhaust I can not get the feller gauge in between the rocker arm and shim. Is there a reason for this as all other valves were spot on. Its just funny when you take the clearances all the other rocker arms are not fully compressed but number 3 exhaust is. Hope someone can help me out with this cheers.

Post by **CMSMJ1** » Tue May 11, 2010 9:47 am

You have turned the motor etc to the right place to take these measurements?

Is it both exhaust valves?

Post by **Neosophist** » Tue May 11, 2010 10:56 pm

pagan1001 wrote:Okay got the new head on but encountered a new problem. I took the valve clearances but for cylinder 3 exhaust I can not get the feller gauge in between the rocker arm and shim. Is there a reason for this as all other valves were spot on. Its just funny when you take the clearances all the other rocker arms are not fully compressed but number 3 exhaust is. Hope someone can help me out with this cheers.

NC24 doesn't have shims?

Old Painless · Post by **Old Painless** » Tue May 11, 2010 11:19 pm

Nope. Valve clearance adjustment is done via a screw and locknut on the rocker arm, the cam lobe pushes the rocker arm onto the top of the valve.

pagan1001 · Post by **pagan1001** » Wed May 12, 2010 12:57 am

Its cool I got it. Haynes manuel is wrong for the nc24. The piston was not at TDC so just did it with good old fashioned eye sight. Got them all in spec. Will fire her up tomorrow so fingers crossed. Cheers.

pagan1001 · Post by **pagan1001** » Thu May 13, 2010 1:05 am

OKAY got her started but there is still something not quiet right......... the best way I can describe it is that it sounds rumbly and heavy like its wet or something........... any ideas on that guys????????????????????????????????????????

Old Painless · Post by **Old Painless** » Thu May 13, 2010 1:47 am

You did your valve clearances with a feeler gauge or by eye ?

NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD

Re: NC24 1987 BAD RATTLING FROM REAR CYLINDER HEAD