NC24 Rear exhausts and collector?

christ044 · Post by **christ044** » Sun Jun 22, 2008 6:16 pm

Hi there,
Iv got a Honda NC24 and im need of the rear exhaust pipes and the collector, does anyone know where I couold get these from?

Many Thanks Chris

Post by **CMSMJ1** » Mon Jun 23, 2008 6:17 pm

Hi Chris,

These parts are rarer than hens teeth in rocking horse cack...

Your best bert is to find a very helpful fabricator to make you some or to find a non rotted one on ebay or here and use that.
The replacement is supposed to be an engine out job.....nightmare for your NC24 owners!

NC21 pipes will fit too...if you can find any..

christ044 · Post by **christ044** » Mon Jun 23, 2008 8:11 pm

Thanks mate,
Must admit iv been looking and realised its an engine out job, luckly enough im rebuilding the bike completely so the engine has to come out anyway!

Ill keep my eyes peeled on here and ebay.

Chris

Post by **spooky** » Mon Jun 23, 2008 11:06 pm

Theres a good how to on here http://www.dunc.freeuk.com/bikes/nc24/nc24.htm mate click on the link at the bottom of the page.

Post by **spooky** » Mon Jun 23, 2008 11:12 pm

Im in the same boat too.

Post by **spooky** » Tue Jun 24, 2008 12:44 am

I found a guy who had s/steel pipe already bent so I cut n welded it to roughly the same shape. just need to rebuild the rest of the bike now.

Lots of bits powder coated, respray to be done,Stainless bolts getting tommorow, new ht leads to make up,clean up all parts underway, shrink wrap some wiring, new screen ordered, new carb inlet rubbers got,new seal kits for front brakes got,new hand grips got, new speedo cable got,new air filter got, new oil filter and removing tool got,rear shock ready for powder coating, wheels to paint (has to be white),new front wheel bearings got,and on and on and on!

christ044 · Post by **christ044** » Tue Jun 24, 2008 8:38 pm

Your alot further on than me then! :D

Are you going to spray paint the wheels or have them powder coated? I can make up my mind which to do.

castrol101 · Post by **castrol101** » Tue Jun 24, 2008 9:07 pm

Are you going to spray paint the wheels or have them powder coated?

If it were me (and i hope it will be if i get the money together

) I would powder coat them

Much harder wearing and IMO looks better.

Post by **spooky** » Wed Jun 25, 2008 1:43 am

christ044 wrote:Your alot further on than me then! :D

Are you going to spray paint the wheels or have them powder coated? I can make up my mind which to do.

Still not sure about that yet, Paint would be easier to repair if they get chipped but powder coating is more hard wearing as castrol101 says and looks better too, but the blaster guy told me not to as its hard to remove powder coating. So still not decided!

Ps. got me some s/steel bolts today.

christ044 · Post by **christ044** » Wed Jun 25, 2008 2:45 pm

Im very much no the route of powder coating, and they shouldnt really chip if they are powder coated

NC24 Rear exhausts and collector?

NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?

Re: NC24 Rear exhausts and collector?