SELEXON'S NC29 Pre Modern Racer
- Yakama
- Site Supporter
- Reactions:
- Posts: 1369
- Joined: Wed Apr 30, 2008 5:27 pm
- Bike owned: NC23s, 29, 30s, MC16
- Location: Oban
Re: SELEXON'S NC29 Pre Modern Racer
Cheers for that will have a look for one cheap
-
- Site Supporter
- Reactions:
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
Re: SELEXON'S NC29 Pre Modern Racer
So just to confirm this will be a complete replacement for the wheel spacer, brake carrier alloy block thing?
If so me want....
If so me want....
- selexon
- Site Supporter
- Reactions:
- Posts: 114
- Joined: Wed Dec 08, 2010 9:55 am
- Bike owned: FZR400R 2TK, CBR400RR NC29
- Location: Launceston, Tasmania
- Contact:
Re: SELEXON'S NC29 Pre Modern Racer
Yes and No,
This in not a under slung unit I don't want to make torque arms etc even though they are cool plus it may cause interference with big bore/aftermarket pipes.
It is a simple replacement caliper bracket that is suited to take the Brembo Caliper.
As the caliper is a two piston opposed unit it needs to run vertical of the axle. Please note I still need to add a locating pivot to the design.
This in not a under slung unit I don't want to make torque arms etc even though they are cool plus it may cause interference with big bore/aftermarket pipes.
It is a simple replacement caliper bracket that is suited to take the Brembo Caliper.
As the caliper is a two piston opposed unit it needs to run vertical of the axle. Please note I still need to add a locating pivot to the design.
- selexon
- Site Supporter
- Reactions:
- Posts: 114
- Joined: Wed Dec 08, 2010 9:55 am
- Bike owned: FZR400R 2TK, CBR400RR NC29
- Location: Launceston, Tasmania
- Contact:
Re: SELEXON'S NC29 Pre Modern Racer
I finally received the new rods from Carrillo.
Talk about little hotties...
Talk about little hotties...
Last edited by selexon on Tue Aug 09, 2011 12:56 pm, edited 1 time in total.
- Yakama
- Site Supporter
- Reactions:
- Posts: 1369
- Joined: Wed Apr 30, 2008 5:27 pm
- Bike owned: NC23s, 29, 30s, MC16
- Location: Oban
Re: SELEXON'S NC29 Pre Modern Racer
Very nice?
-
- Senior Member
- Reactions:
- Posts: 1160
- Joined: Tue Apr 29, 2008 10:01 pm
- Bike owned: Already 20% of NC29...
- Location: Seattle, USA
- Contact:
Re: SELEXON'S NC29 Pre Modern Racer
As I see new rod little bit longer. Are you going to change pistons ?
-
- Site Supporter
- Reactions:
- Posts: 1571
- Joined: Wed Apr 30, 2008 4:47 pm
- Bike owned: CCM404 SM, CBR4/6 in progress
- Location: Nottingham U.K
- selexon
- Site Supporter
- Reactions:
- Posts: 114
- Joined: Wed Dec 08, 2010 9:55 am
- Bike owned: FZR400R 2TK, CBR400RR NC29
- Location: Launceston, Tasmania
- Contact:
Re: SELEXON'S NC29 Pre Modern Racer
The length is the same as std, I just haven't lined then up even when taken the photo.PARUS wrote:As I see new rod little bit longer. Are you going to change pistons ?
The lower part of the rod where the bolts screw into is larger so gives it that little bit bigger look.
-
- Senior Member
- Reactions:
- Posts: 1160
- Joined: Tue Apr 29, 2008 10:01 pm
- Bike owned: Already 20% of NC29...
- Location: Seattle, USA
- Contact:
Re: SELEXON'S NC29 Pre Modern Racer
[quote="selexon"][quote="PARUS"]As I see new rod little bit longer. Are you going to change pistons ?[/quote]
The length is the same as std, I just haven't lined then up even when taken the photo.
The lower part of the rod where the bolts screw into is larger so gives it that little bit bigger look.[/quote]
What about weight compare with stc? Are this titanium or steel?
What is the part number, because I can't find them on manufacturer website ?
The length is the same as std, I just haven't lined then up even when taken the photo.
The lower part of the rod where the bolts screw into is larger so gives it that little bit bigger look.[/quote]
What about weight compare with stc? Are this titanium or steel?
What is the part number, because I can't find them on manufacturer website ?
- selexon
- Site Supporter
- Reactions:
- Posts: 114
- Joined: Wed Dec 08, 2010 9:55 am
- Bike owned: FZR400R 2TK, CBR400RR NC29
- Location: Launceston, Tasmania
- Contact:
Re: SELEXON'S NC29 Pre Modern Racer
Hi Parus,
The Rods are 12g heavier then the std Honda items.
They are made from Carrillo's own proprietary chrome, nickel, moly, vanadium alloy mix.
I had to specially order the rods, it took them about 6-7 weeks to complete production.
The Rods are 12g heavier then the std Honda items.
They are made from Carrillo's own proprietary chrome, nickel, moly, vanadium alloy mix.
I had to specially order the rods, it took them about 6-7 weeks to complete production.