DIY GK76A Engine Stand
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Settled in member
- Reactions:
- Posts: 98
- Joined: Tue Feb 02, 2016 8:57 pm
- Bike owned: GK76A 1993 and 1990
- Location: West Midlands
DIY GK76A Engine Stand
As I'll be working on the engine for the next few weeks (or months!) I knocked this DIY stand up from some timber blocks I had lying around.
Quite pleased with it.
It may not look much, but it does the job and it cost me just my time, unlike some of the explensive stands I've seen.
The tricky part was getting the dimensions exactly right.
Hopefully It's solid enough for some serious torquing.
http://ibb.co/gfxKLk
http://ibb.co/jDqTD5
http://ibb.co/fe0vt5
http://ibb.co/dW6qRQ
Quite pleased with it.
It may not look much, but it does the job and it cost me just my time, unlike some of the explensive stands I've seen.
The tricky part was getting the dimensions exactly right.
Hopefully It's solid enough for some serious torquing.
http://ibb.co/gfxKLk
http://ibb.co/jDqTD5
http://ibb.co/fe0vt5
http://ibb.co/dW6qRQ
-
- Settled in member
- Reactions:
- Posts: 85
- Joined: Fri Jun 19, 2015 6:14 am
Re: DIY GK76A Engine Stand
Looks bloody good! Need to get me one I think!
-
- Settled in member
- Reactions:
- Posts: 98
- Joined: Tue Feb 02, 2016 8:57 pm
- Bike owned: GK76A 1993 and 1990
- Location: West Midlands
Re: DIY GK76A Engine Stand
OK, I've had to make a few mod's to my DIY stand to make it a bit stronger.
It was fine with the engine just resting, but as soon as I started removing some of the corroded bolts it started wobbling under the strain.
I've added some struts and braces that I picked up from Wickes for peanuts.
It's as solid as it needs to be now, and ideal for top end rebuilds or any work under the side casings, clutch etc.
If anyone needs the dimensions or specs, send me a message.
https://image.ibb.co/dhQAgQ/P1020103.jpg
https://image.ibb.co/ipW5Fk/P1020102.jpg
https://image.ibb.co/ghCCvk/P1020101.jpg
https://image.ibb.co/mzLzak/P1020100.jpg
https://image.ibb.co/hP3Kak/P1020099.jpg
It was fine with the engine just resting, but as soon as I started removing some of the corroded bolts it started wobbling under the strain.
I've added some struts and braces that I picked up from Wickes for peanuts.
It's as solid as it needs to be now, and ideal for top end rebuilds or any work under the side casings, clutch etc.
If anyone needs the dimensions or specs, send me a message.
https://image.ibb.co/dhQAgQ/P1020103.jpg
https://image.ibb.co/ipW5Fk/P1020102.jpg
https://image.ibb.co/ghCCvk/P1020101.jpg
https://image.ibb.co/mzLzak/P1020100.jpg
https://image.ibb.co/hP3Kak/P1020099.jpg