NC23 FCR32 jetting

Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Post Reply
LeiWulong
Settled in member
Reactions:
Posts: 6
Joined: Sat Jan 21, 2017 8:48 am
NC23 FCR32 jetting

Post by LeiWulong » Sun Jul 22, 2018 4:12 pm

Hello all!
Does anyone have experience of tuning FCR32/33 on NC23?
What camshafts did you use? Stock/HRC?
What was the jets size?

I am stuck in tuning FCR32 on my CB-1 with stock NC23 camshafts...

My FCR32 came from Yahoo and were used on a CB-1 (camshaft specification is unknown :( ) with these jets:
F.Main: #132
A.Main: #200
F.Slow: #48
A.Slow: #110

We made several dyno runs with steb-by-steb lowering main jet. At the moment my jet is #105 (which is stock size for CV carb for both CB-1 and NC23).
Even with #105 jet I have too rich mixture at the top of RPM (beginning from 12000).

Thanks in advance.

Image

sa.racing
Site Supporter
Site Supporter
Reactions:
Posts: 159
Joined: Fri May 02, 2008 7:08 pm
Bike owned: NC29 Race
Location: Surrey
Contact:
Re: NC23 FCR32 jetting

Post by sa.racing » Thu Jul 26, 2018 9:31 pm

It would take me a month to write what this guy has already taken the time to put together,

http://www.factorypro.com/tech/tech_tun ... s,Pat.html

Read it all thoroughly and start from the beginning most dyno operators have never even seen a set of FCR's let alone worked on them follow the guide these guys know what their talking about
Si

LeiWulong
Settled in member
Reactions:
Posts: 6
Joined: Sat Jan 21, 2017 8:48 am
Re: NC23 FCR32 jetting

Post by LeiWulong » Fri Jul 27, 2018 6:00 pm

sa.racing wrote:
Thu Jul 26, 2018 9:31 pm
It would take me a month to write what this guy has already taken the time to put together,

http://www.factorypro.com/tech/tech_tun ... s,Pat.html

Read it all thoroughly and start from the beginning most dyno operators have never even seen a set of FCR's let alone worked on them follow the guide these guys know what their talking about
Si
Hi! Thank you for reply. Actually we tune it together with dyno operator :)

Thank you for this article - we have already read it (and print it and put it near Dyno before tuning) :)
We also have read this:
http://www.factorypro.com/tech_tuning_p ... gasEGA.htm
https://www.keihin-na.com/assets/1/7/slide_valve.pdf

Our problem is on the first step: choosing the main fuel jet on top RPM.
It's current size is #105 (started from #132) and still we have rich mixture on the top. I don't want to get lower, because this jet size will be less then stock CB-1/NC23.
So I am sure that I use wrong camshaft (stock camshaft from NC23).
I am waiting for GF Racing race camshaft to prove my theory :)

My current best result is 57 hp on the shaft with #116 main jet and still can't get to normal AFR on the top.
Image

moforockband
Familiar Member
Reactions:
Posts: 388
Joined: Wed Jun 03, 2015 9:41 am
Bike owned: GK73a SP CRM250 mk3
Re: NC23 FCR32 jetting

Post by moforockband » Sat Jul 28, 2018 5:37 pm

GF racing will be able to advise. But you can widen the Main air jet (MAJ) by one size to lean the mixture curve also. It works slightly differently to just the main jet. It will lean the mixture off more at the top end than the lower end of the revs.
Are you using an airbox?? You will find more hp, using a front ram feed airbox than stand alone pod filters (which can be restrictive).
Are your pod filters pulling in warm air from the heat of the engine? This will make it run rich also.


Post Reply