Serious question
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Site Supporter
- Reactions:
- Posts: 159
- Joined: Fri May 02, 2008 7:08 pm
- Bike owned: NC29 Race
- Location: Surrey
- Contact:
Re: Serious question
Hi Ian,
Where are you located? I have an old swingarm here from my old race bike which has had some lugs and a sharksfin made and welded on if your local you can have it as I'm sick of keep walking into the bloody thing,
I'm in Surrey (about 2 mins from Hampton court palace) if not don't worry I'll just carry on using it as a coat hanger
Si
Where are you located? I have an old swingarm here from my old race bike which has had some lugs and a sharksfin made and welded on if your local you can have it as I'm sick of keep walking into the bloody thing,
I'm in Surrey (about 2 mins from Hampton court palace) if not don't worry I'll just carry on using it as a coat hanger
Si
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Re: Serious question
Si,
Huge apologies I have only just seen this post.
That is a very generous offer from you , but I am now sorted for a swingarm/stand solution.
Apologies once again.
Ian
Huge apologies I have only just seen this post.
That is a very generous offer from you , but I am now sorted for a swingarm/stand solution.
Apologies once again.
Ian
-
- Regular Member
- Reactions:
- Posts: 695
- Joined: Wed Jun 03, 2009 9:39 pm
- Bike owned: Cbr400rr nc29 type8 NSR250
- Location: West Midlands
Re: Serious question
How did you sort it in the end?
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Re: Serious question
Dunk
I had a 12mm bar turned down to 10mm on one end, had the 10mm end threaded and that then slips through the hollow axle on my bike.
I have fixed a paddock stand bobbin on one end, and have tapped the other one to suit the 10mm thread on the other end.
Ian
I had a 12mm bar turned down to 10mm on one end, had the 10mm end threaded and that then slips through the hollow axle on my bike.
I have fixed a paddock stand bobbin on one end, and have tapped the other one to suit the 10mm thread on the other end.
Ian
-
- Regular Member
- Reactions:
- Posts: 695
- Joined: Wed Jun 03, 2009 9:39 pm
- Bike owned: Cbr400rr nc29 type8 NSR250
- Location: West Midlands
Re: Serious question
How do you get the wheel out if the stand goes through the axle?Boggieman wrote:Dunk
I had a 12mm bar turned down to 10mm on one end, had the 10mm end threaded and that then slips through the hollow axle on my bike.
I have fixed a paddock stand bobbin on one end, and have tapped the other one to suit the 10mm thread on the other end.
Ian
Sent from my iPhone using Tapatalk
-
- Settled in member
- Reactions:
- Posts: 20
- Joined: Sun May 21, 2017 9:00 pm
Re: Serious question
Hi Dunk
I just unscrew the bobbin from the 10mm end and pull the bar out, and the axle is back to normal.
Ian
I just unscrew the bobbin from the 10mm end and pull the bar out, and the axle is back to normal.
Ian