TAKING ORDERS: Cosworth 56mm & 57mm Pistons for 2016
Forum rules
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
Please can you post items for sale or wanted in the correct For Sale section. Items / bikes for sale here will be removed without warning. Reasons for this are in the FAQ. Thanks
-
- Settled in member
- Reactions:
- Posts: 154
- Joined: Wed Apr 30, 2008 8:11 pm
- Location: Cumming, GA USA
- Contact:
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
Tell me you didn't buy one of those horrific little KTM 390 mopeds?cajun wrote:I was just sticking my head in to say hello. I'm too broke right now with trying to do some MotoAmerica rounds to do anything with the 29. But eventually, I will be putting it back together and putting it back together in a big way. So I will be in touch.
Hope you're feeling better Mike. I will have to give you a call so we can catch up. Have you posted up about the Castec here?
-
- Settled in member
- Reactions:
- Posts: 50
- Joined: Sat May 17, 2008 3:10 pm
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
Hi Mike.
I'm also interested.
Again, can I check what the full cost would be incl rods?
Would be looking at 1-2 sets of the 57mm with +3mm rods.
Re: the rods - you mention HRC / Gforce - are these the Carrillo ones you have used or a different supply?
Please keep us updated.
Thanks!
I'm also interested.
Again, can I check what the full cost would be incl rods?
Would be looking at 1-2 sets of the 57mm with +3mm rods.
Re: the rods - you mention HRC / Gforce - are these the Carrillo ones you have used or a different supply?
Please keep us updated.
Thanks!
-
- Settled in member
- Reactions:
- Posts: 50
- Joined: Sat May 17, 2008 3:10 pm
-
- Familiar Member
- Reactions:
- Posts: 311
- Joined: Thu May 29, 2008 5:58 am
- Bike owned: VTR-250, VFR400RR,
- Location: Santa Clara County, California, USA
- Contact:
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
Hi guys.
I am sorry for going missing on you. Life's been giving me some fits and twists lately. Unfortunately, while recovering from my 3rd cervical (neck) spine surgery I somehow broke my lumbar (lower) back in 2 places. This, caused me to lose my badass Dyno Engineer job with Honda Racing. So, now I am going in for yet another spinal surgery next week.
Needless to say, I have done nothing with the Cosworth pistons. I was able to source a new ring, but that would leave everyone with the previous pistons out in the cold for rings. So, I am still holding off on doing anything until I have exhausted the possibilities for getting new rings made to the Yamaha spec. I will work on this while recovering from this next surgery.
Don't be afraid to poke. I'm not a hornets nest. Just super busy and now very distracted.
Cheers,
Mike Norman
I am sorry for going missing on you. Life's been giving me some fits and twists lately. Unfortunately, while recovering from my 3rd cervical (neck) spine surgery I somehow broke my lumbar (lower) back in 2 places. This, caused me to lose my badass Dyno Engineer job with Honda Racing. So, now I am going in for yet another spinal surgery next week.
Needless to say, I have done nothing with the Cosworth pistons. I was able to source a new ring, but that would leave everyone with the previous pistons out in the cold for rings. So, I am still holding off on doing anything until I have exhausted the possibilities for getting new rings made to the Yamaha spec. I will work on this while recovering from this next surgery.
Don't be afraid to poke. I'm not a hornets nest. Just super busy and now very distracted.
Cheers,
Mike Norman
-
- Moderators
- Reactions:
- Posts: 9358
- Joined: Fri Jul 04, 2008 1:01 pm
- Bike owned: CBR954
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
get well soon fella, hope your next surgery is the last you needg-force performance wrote:Hi guys.
I am sorry for going missing on you. Life's been giving me some fits and twists lately. Unfortunately, while recovering from my 3rd cervical (neck) spine surgery I somehow broke my lumbar (lower) back in 2 places. This, caused me to lose my badass Dyno Engineer job with Honda Racing. So, now I am going in for yet another spinal surgery next week.
Needless to say, I have done nothing with the Cosworth pistons. I was able to source a new ring, but that would leave everyone with the previous pistons out in the cold for rings. So, I am still holding off on doing anything until I have exhausted the possibilities for getting new rings made to the Yamaha spec. I will work on this while recovering from this next surgery.
Don't be afraid to poke. I'm not a hornets nest. Just super busy and now very distracted.
Cheers,
Mike Norman
xivlia wrote:i dont go fast on this bike so really do not need a rear brake.. /
vic-vtrvfr wrote:Ask xivlia for help, he's tackled just about every problem u could think of...
- Yakama
- Site Supporter
- Reactions:
- Posts: 2676
- Joined: Wed Apr 30, 2008 5:27 pm
- Bike owned: NC23s, 29, 30s, MC16
- Location: Oban
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
What about this company, they seem to produce Pistons for various 400s already and they make rings for the nc30
www.scheuerlein.de
www.scheuerlein.de
- mruehl34
- Site Supporter
- Reactions:
- Posts: 672
- Joined: Wed Apr 30, 2008 8:06 pm
- Location: Germany
- Contact:
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
I can ask them. But first Mike have to tell us if he can make some pistons
Michael
Michael
- Yakama
- Site Supporter
- Reactions:
- Posts: 2676
- Joined: Wed Apr 30, 2008 5:27 pm
- Bike owned: NC23s, 29, 30s, MC16
- Location: Oban
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
Perhaps they could make the Pistons too?
- fourfingers
- NWAA Supporter
- Reactions:
- Posts: 188
- Joined: Sun May 18, 2008 12:32 am
- Bike owned: NC30RK,NC35RR
- Location: Madrid
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
Michael,
They also have the stock Yamaha 1WG-11610-00-00 rings (56mm), could you please ask them if they could make them in 57mm for the 2009 coswoth pistons?.
thanks
They also have the stock Yamaha 1WG-11610-00-00 rings (56mm), could you please ask them if they could make them in 57mm for the 2009 coswoth pistons?.
thanks
- mruehl34
- Site Supporter
- Reactions:
- Posts: 672
- Joined: Wed Apr 30, 2008 8:06 pm
- Location: Germany
- Contact:
Re: Cosworth 56mm & 57mm NC29, NC30, NC35 Pistons for 2016
I talked to Scheuerlein, they told me that they have the 57mm pistonrings include the oil ring in stock.
A set will cost 199,90€ without shipping. Scheuerlein had more than 10 sets in stock.
Michael
A set will cost 199,90€ without shipping. Scheuerlein had more than 10 sets in stock.
Michael